Kegland Oxebar kegs/dispense

[Clint]

Something like this..

 

[Laner]

View attachment 106134
Something like this..

I use one of those and a duotight party tap, they work very well if I get my carbonation right.

 

[Clint]

Will it matter what size gas line? The reg I'm looking at comes with a 3/8" push fit to which I can connect to the same size Duotight on the keg with a length of 3/8,so easy to do. Does gas line length matter?

 

[Clint]

I've also seen videos of the beer tube inside the keg being cut shorter. Is this necessary?

 

[Larse]

View attachment 106134
Something like this..

Ok, that's what I was talking about too. Often called a picnic tap. There are others that connect directly to the keg that look very like kegerator taps. As I said, the length of the line is important, otherwise you'll get a glass of foam.

Will it matter what size gas line? The reg I'm looking at comes with a 3/8" push fit to which I can connect to the same size Duotight on the keg with a length of 3/8,so easy to do. Does gas line length matter?

No, Gas line can be any diameter and length. I use 5/16" because then I only need to have 8mm fittings and not a mess of different sizes lying around. Just make sure your gas line isn't so short that it's putting pressure on the connectors and leaking.

 

[Larse]

I've also seen videos of the beer tube inside the keg being cut shorter. Is this necessary?

No idea, Assume it's a floating dip tube, so it has to be long enough to reach the bottom. So maybe it's supplied a bit longer and people cut off the excess.

 

[Clint]

Thanks again!! I think the tap I pictured comes with 1.5m of pipe. I'm wondering if,as they're a complete kit,the line length etc has been tested?

 

[Larse]

Thanks again!! I think the tap I pictured comes with 1.5m of pipe. I'm wondering if,as they're a complete kit,the line length etc has been tested?

Maybe. But carbonation levels vary, so it can't be spot on for everything, Just looked it up there, it's 3/16 (4.76mm) which at 12psi may be a bit fobby at 1.5m. For contrast, I use 4mm hose in my kegerator cut to 2.1m, when I used 3/16", I had it at 4m and it was too fobby, so I changed to 4mm.

 

[Clint]

Hmmm...some things to consider. I might just get one pre made tap and see how it works then if it needs fettling get some longer line.

 

[Larse]

Hmmm...some things to consider. I might just get one pre made tap and see how it works then if it needs fettling get some longer line.

Yeah, beer line is cheap, so you can always add more. That tap uses push on fittings, so no problem to take off the 3/16" section and replace with a longer one.

 

[Dazzelknight]

Iv just got the 20lt from the TMM sale, very impressed.

 

[Clint]

I take it you got the kit? Have you used the tap?

 

[Clint]

Another question....set up with party tap....in between sessions what do you do with the tap to keep it clean/bug free?
Could it be submerged in a jar of sanitiser?

 

[Dazzelknight]

Yeah ,, it’s obvious budget but works perfectly.. only gripe I got was the fittings ,, I did a leak test in a bucket of water and both push in gas valves bubbled but I sorted it with a couple of rubber O’ rings

 

[Dazzelknight]

Can just take the tap off when not using and rinse

 

[Larse]

Another question....set up with party tap....in between sessions what do you do with the tap to keep it clean/bug free?
Could it be submerged in a jar of sanitiser?

You can disconnect the beer line and run water through it and clean the connectors separately. Or just put a carbonation cap on a PET bottle full of cleaner and run it through the tap and then follow up with sanitiser. Or just water and sanitiser and leave it.

 

[Laner]

You can disconnect the beer line and run water through it and clean the connectors separately. Or just put a carbonation cap on a PET bottle full of cleaner and run it through the tap and then follow up with sanitiser. Or just water and sanitiser and leave it.

I use carb cap and pet bottle. Good squeeze and the line is clear