I have the shiney feaver

[snail59]

This arrived today Absolute BARGAIN :whistle:

It holds 14lts of water & is insulated. :thumb:
I plan to use it as a mash tun for 15ltr brew lengths. Does that sound like a reasonable idea.

 

[corby_brewer]

Nice find Mick :thumb: All you need now is for MD to make you a FB for it.
Did it come with a lid?

 

[snail59]

Yes Dave it has an insulated lid. False bottom maybe a non starter the hole is smaller than the inside.

 

[Muddydisco]

Fb's can be made with hinges to get in those awkward spots. As long as the hole is no smaller than Half of the diameter I can get one in there :thumb:

Looks good for the job :thumb:

 

I have the shiney feaver

Sounds like the credit card's going to take a bashing.
Shiney shiney shiney :twisted:

 

[snail59]

I have the shiney feaver

Sounds like the credit card's going to take a bashing.
Shiney shiney shiney :twisted:

Not true Eric. Shop wisely bargains are out there. I got my 37ltr Burco for £30 this urn was £20.03 including delivery off fleabay.

Fb's can be made with hinges to get in those awkward spots. As long as the hole is no smaller than Half of the diameter I can get one in there :thumb:

Looks good for the job :thumb:

MD The whole is much bigger than half the diameter. Will measure up and e mail you for a quote :thumb:

If I use a false bottom does this mean I would not need a strainer in the tun???????.

 

[Muddydisco]

The bottom is the Strainer as you put it.
I'll want the Diameter, the position of the tap inlet, the Height above the bottom to the centre of the tap inlet and the rough size of the tap inlet.

 

[Cussword]

The bottom is the Strainer as you put it.
I'll want the Diameter, the position of the tap inlet, the Height above the bottom to the centre of the tap inlet and the rough size of the tap inlet.

What about his inside leg

 

What about his inside leg

How wonderful, the art of humour is not dead!

 

[fermentall]

Agreed not like the art of English football :grin:

 

[snail59]

How can I make this shiny fetish go away.

Just bought THIS

 

[corby_brewer]

Nice one Mick. How are you planning on connecting it to your Corny? Are you going to build a kegerator?

 

[markp]

How can I make this shiny fetish go away.

Just bought THIS

That's a beauty of a tap

 

[Sean_Mc]

Nice :thumb:

Just put that on watch, would love to replace my plastic taps with three of those

 

[snail59]

Nice one Mick. How are you planning on connecting it to your Corny? Are you going to build a kegerator?

A Kegerater is in the planning stage Dave :thumb:

 

[snail59]

Got my false bottom from MD today it fits like a glove top work fella :thumb:

Also got my Shiny tap. Anyone know where I can get A John Guest Fitting to connect tap to the Corni. I assume you can get a 15mm female threaded to 3/8th pipe connector????.

 

[corby_brewer]

Mick.
I have a box of assorted fittings, if you can post a picture of what you want ill see if i have one.

 

[snail59]

What I need Dave will have a female fitting to screw onto the tap (a nut from a 15mm compression fitting srews on) with a speedfit to take 3/8th beer line so I can connect tap to Corni.
So I need to join these

 

[corby_brewer]

Mick, iv'e had a look through my box of bit and come acroos this, i think its what your looking for but not 100% sure. if you PM me your address ill stick it in the post tomorrow.

 

[snail59]

PM sent :thumb: