Ballihoo equipment, PB pressure, St Peters Ruby Red; looking for advice.

[Jonneyney]

Hello all!

Noob/lurker here.

Just looking for some advice. I have started my first brew of a St Peters Ruby Red, kit. Followed instructions, but listened to advice here on the forum about extending the amount of time in the FV for example. Brew was in FV for approx 2 weeks, kept at 18-20 celsius. All looking ok so far.

Transferred over to PB, primed with 70g of sugar about a week ago, however temps have dropped to around 16 degrees. Gave it a small taste today, bit fruity for me but otherwise quite nice. Still cloudy but hopefully that should clear up in the coming weeks.

However the beer is resoundingly flat, I'm looking to figure out why exactly and what I can do to save the beer.

Attached are some images of the equipment I have. (These are from my second PB, so that is why they are not in-use currently)

The cap has a valve that I can use to top up pressure with Co2 canisters, although as far as I am aware that should only be done once the keg has been drunk somewhat.

Is there anyway I can check if the PSI is correct? How will I know if the sugar is working with the yeast and producing Co2?
I have a PSI tire gauge that apparently I can pop on top of the valve to measure, however this either doesn't fit or I'm not using it right as it seems to do nothing?

Any advice would be appreciated, I've got an IPA in the FV at the moment so I'd like to get this process down.

Thank you in advance!

(PS for the third image, any advice on how to make sure the rubber ring connects to the plastic top properly, it keeps popping out for some reason)

 

[Larse]

Have you any idea of gravity readings at the start and when you kegged?

Also, looks like there was no secondary fermentation in the keg and hence it's flat. Maybe try and get it warmed up a bit first?

What method are you using to add CO2? Are they the small sparklet bulbs or something bigger?

 

[Jonneyney]

Have you any idea of gravity readings at the start and when you kegged?

Also, looks like there was no secondary fermentation in the keg and hence it's flat. Maybe try and get it warmed up a bit first?

What method are you using to add CO2? Are they the small sparklet bulbs or something bigger?

Thanks for the response Larse

As this is my first kit, I foolishly did not take gravity readings (note for next time)

I've now put it somewhere that is closer to 19-20 degrees.

For CO2 I've only added the required sugar, I have this thing below, alongside some CO2 capsules (I have not used these yet)

 

[Rwilts]

70g doesnt sound like enough sugar to carbonate / condition the beer to me, HOWEVER I dont use a PB and the only time I did (many years ago, it failed to hold pressure).

So in furtherance to @Larse good points , i would check the amount of fermentable needed (you might have this right) and also make sure that the PB is well sealed, or all your produced CO2 will leak away and the beer will continue to be flat.

Also just for info the bulbs will only be enough to maintain a serving pressure once the PB is carbonated , they are not enough to carbonate your beer.

All of the above you probably know :)

 

[Larse]

Thanks for the response Larse

As this is my first kit, I foolishly did not take gravity readings (note for next time)

I've now put it somewhere that is closer to 19-20 degrees.

For CO2 I've only added the required sugar, I have this thing below, alongside some CO2 capsules (I have not used these yet)

View attachment 106063

Yeah, those are the sparklets bulbs I mentioned. About 12g of CO2 in each I think.

The problem with those plastic kegs (I used to use them in the distant past) is that there's a lot of headspace in them which takes forever to fill with naturally created CO2 and so I never got decent carbonation in them.

If I were you, I'd probably blast a few of them into the keg to get the pressure up so there's some chance of carbonation.

 

[starseeker]

Have you applied a small amount of vaseline or similar to the sealing ring (both sides) before assembling ? This helps to ensure you have a air tight seal ,

 

[Dazzelknight]

Sounds like u have a leak …. As above .. Vaseline your o’ring,, do not over tighten.. fire in a Co2 bulb.. wipe some washing up liquid and a dash of water round ur seals (top and tap) if no bubbles ur good to go